Has anyone else had this happen?
I had a flat but when I took the wheel off, separated the rim, removed and patched the tube, put all back together...inflated...AND TORE A HOLE IN THE TUBE BY PINCHING IT BETWEEN THE RIM HALVES!
and not just once...I have one spare tube with two 1/4" holes on the inside right where the rim meets and now the one one the scoot (rear) is flat (again, after repairing the original flat) and I KNOW I MADE SURE IT WASN'T PINCHED.
WHAT THE !@#$ AM I DOING WRONG OR MISSING?
i think these are the original tubes from 2012 on right now, front hasn't shown any problems.
pinch flats--AAARRRGGGGHH!
Moderator: Modern Buddy Staff
- EvilNerdLord
- Member
- Posts: 352
- Joined: Mon May 27, 2013 9:49 pm
- Location: Marysville, CA
pinch flats--AAARRRGGGGHH!
Professional nerd, Cube dweller, and wannabe Evil Overlord (OK, maybe not too evil or lord over more than I can manage...well, on second thought make that Suburbanite just trying to make his way in the world as best he can)
- Stanza
- Member
- Posts: 575
- Joined: Mon Jan 29, 2018 8:34 pm
- Location: Chicago
- EvilNerdLord
- Member
- Posts: 352
- Joined: Mon May 27, 2013 9:49 pm
- Location: Marysville, CA
I thought i did have 'a bit of air' in...buuuut nooo, opposite the stem got pinched.
need to look into split replacement.
need to look into split replacement.
Professional nerd, Cube dweller, and wannabe Evil Overlord (OK, maybe not too evil or lord over more than I can manage...well, on second thought make that Suburbanite just trying to make his way in the world as best he can)
- charlie55
- Member
- Posts: 1924
- Joined: Tue Apr 08, 2008 6:47 pm
- Location: New Jersey
- EvilNerdLord
- Member
- Posts: 352
- Joined: Mon May 27, 2013 9:49 pm
- Location: Marysville, CA
discovered that my (second) patch (there was already a patch, ran over a nail) didn't hold, had to peel it off and redo the fix.
so...
1) had flat from nail
a) took wheel apart to repaired flat
b) reassembled wheel
2) new flat from pinching tube during reassembly 1b)
a) took wheel apart to repaired flat
b) reassembled wheel
3) repaired tire/tube goes flat again
a) WTF!?!?!?
b) post WTF!?!? on modern buddy
c) gleam answers of hivemind
4) HAVE AH-HA! moment
a) took wheel apart to repaired flat
a.a) discovered patched fail on pinch hole from 3) remove/rerepair
b) reassembled wheel
5) inflate to stated pressure for rear (35 psi) seems too much, but that's what the SOM says as well as the tire itself...so OK
a) so far, so good
![Very Happy :D](./images/smilies/icon_biggrin.gif)
so...
1) had flat from nail
a) took wheel apart to repaired flat
b) reassembled wheel
2) new flat from pinching tube during reassembly 1b)
a) took wheel apart to repaired flat
b) reassembled wheel
3) repaired tire/tube goes flat again
a) WTF!?!?!?
b) post WTF!?!? on modern buddy
c) gleam answers of hivemind
4) HAVE AH-HA! moment
a) took wheel apart to repaired flat
a.a) discovered patched fail on pinch hole from 3) remove/rerepair
b) reassembled wheel
5) inflate to stated pressure for rear (35 psi) seems too much, but that's what the SOM says as well as the tire itself...so OK
a) so far, so good
![Very Happy :D](./images/smilies/icon_biggrin.gif)
Professional nerd, Cube dweller, and wannabe Evil Overlord (OK, maybe not too evil or lord over more than I can manage...well, on second thought make that Suburbanite just trying to make his way in the world as best he can)
-
- Member
- Posts: 12
- Joined: Mon Sep 23, 2013 8:49 pm
- Location: Georgia
rear tire change advice
After patching/replacing, do you have a recommendation? I picked up a nail and need to patch/replace but haven't done it before. This the Stella Auto 125. I was curious if I should try to repair or replace and what advice you have for someone with limited experience and tools.
-
- Member
- Posts: 76
- Joined: Tue May 30, 2017 6:31 pm
There’s some good advice already in this thread. Replace the damaged tube with a new one. The only tool needed is a 13mm socket wrench.
One thing - assemble the new tube, rim and tire, fill the tube with some air, then loosen the nuts and use an old credit card to push between the rims, making sure the inner tube is not being pinched.
I’ve been riding on tubeless rims for a year or so now and recommend them.
One thing - assemble the new tube, rim and tire, fill the tube with some air, then loosen the nuts and use an old credit card to push between the rims, making sure the inner tube is not being pinched.
I’ve been riding on tubeless rims for a year or so now and recommend them.