2008 125
I think the front wheel is out of balance. Vibes over 35 mph.
Can't use my trusty Harbor Frt. motorcycle wheel balancer: its axle is 1/2 inch where the Buddy front axle is 12 mm.
Can't find a 12mm rod.
Can't balance on the bike, usually you can remove the front caliper and balance it, but this Buddy has that speedometer fitting (increased drag).
Any ideas?
balancing Buddy tire
Moderator: Modern Buddy Staff
-
- Member
- Posts: 139
- Joined: Mon Apr 02, 2018 12:07 am
- Location: Lower Alabama
-
- Member
- Posts: 111
- Joined: Wed Dec 05, 2018 7:58 pm
- Location: Charleston
Re: balancing Buddy tire
Does the wheel rim look to be out of round or bent it you spin it when the scoot is on the center stand?
Does the tire look to have irregular wear spots?
Just thinking.
Does the tire look to have irregular wear spots?
Just thinking.
-
- Member
- Posts: 721
- Joined: Thu Jul 12, 2012 3:40 am
- Location: Lake Geneva, WI
Re: balancing Buddy tire
If you pull the axle out you can remove the part that connects the speedometer cable to the front wheel. Then put the axle back in and you should be down to almost no drag.
-
- Member
- Posts: 8
- Joined: Sat Dec 28, 2019 9:09 pm
- Location: Eugene, OR
Re: balancing Buddy tire
I purchased a Marc Parnes static setup:
http://www.marcparnes.com/Motor_Scooter ... lancer.htm
Barely fits but does, and now my Buddy 125's vibes are reduced after balancing both front and rear wheels.
My $0.02
http://www.marcparnes.com/Motor_Scooter ... lancer.htm
Barely fits but does, and now my Buddy 125's vibes are reduced after balancing both front and rear wheels.
My $0.02
-
- Member
- Posts: 139
- Joined: Mon Apr 02, 2018 12:07 am
- Location: Lower Alabama
Re: balancing Buddy tire
After re-checking the tires, both are dated 2008.... So I'm replacing both. Pity, the bike is a 2008 with only 2,000 or so miles!
I did use the front axle to check the balance. I think the small weight and diameter, and bearing drag, conspire against an accurate balance.
BUT- The front tire itself is out-of-round by about 1/10 inch. So there ya go.....
I did use the front axle to check the balance. I think the small weight and diameter, and bearing drag, conspire against an accurate balance.
BUT- The front tire itself is out-of-round by about 1/10 inch. So there ya go.....
-
- Member
- Posts: 721
- Joined: Thu Jul 12, 2012 3:40 am
- Location: Lake Geneva, WI
Re: balancing Buddy tire
Something to consider when buying new tires is that some 10" are made better and are more balanced. Tires like the Pirelli Angels don't even come with the dot to mark where the value should be. I have run them for a while and they are quite smooth riding, even with slightly out of balance wheels. I believe that Michelin tires are also balanced enough that they don't need a dot.
On the other hand I have ridden some brand new Kendas that were really out of balance from the factory.
- babblefish
- Member
- Posts: 3118
- Joined: Tue Dec 04, 2007 8:42 am
- Location: San Francisco
Re: balancing Buddy tire
My local dealer says he's never had to balance a small scooter tire/wheel so I took his advise and didn't bother balancing my tires/wheels for the last two tire changes. I've never run into any vibration problems on my Buddy and I ride at speeds up to 65 mph. I generally buy Michelin or Heidenau tires. Maybe I've just been lucky.
Some people can break a crowbar in a sandbox.