Repainting Spare Wheel

The original 2-stroke Genuine scooter and its 4-stroke manual and automatic offspring

Moderator: Modern Buddy Staff

Post Reply
User avatar
johnk
Member
Posts: 166
Joined: Mon Sep 03, 2018 9:42 pm

Repainting Spare Wheel

Post by johnk »

When I bought my 2003 2T a few months ago, it had not been well cared for. All three tires were date-stamped from 2001. I couldn't get the spare tire off the wheel because the inside was so full of rust. I had to cut the tire widthwise to break it free of the wheel. So I decided to repaint the spare wheel.

I first cleaned them off with soap, and then sanded. It took me about an hour per half-wheel to sand the rust down by hand. I'm planning to buy a powertool before attempting this again. I did most of the heavy sanding with 80-grit, then finished with 180, 400, and 1500. I was very glad I used a dust mask. After sanding, I wiped everything down with rubbing alcohol.

I decided to cover the entire wheel in primer and paint the outer sides black. Here are the "before" pictures. I'll post the "after" pictures when the paint dries. Due to the sanding, plus all the waiting between coats (3 coats of primer and 3 coats of color), this took about four hours.
Attachments
wheel 3.jpg
wheel 3.jpg (170.15 KiB) Viewed 1694 times
wheel 2.jpg
wheel 2.jpg (169.04 KiB) Viewed 1694 times
wheel 1.jpg
wheel 1.jpg (193.98 KiB) Viewed 1694 times
User avatar
johnk
Member
Posts: 166
Joined: Mon Sep 03, 2018 9:42 pm

Post by johnk »

The wheel came out looking pretty good. Not perfect, but a thousand times better than it was.

I used Rust-Oleum primer and Dupli-Color Wheel Paint. I think it could have used another few coats, and much more time to dry between coats, as well as more time to dry (more than overnight) before I put the wheel back together. The paint was still very soft this morning, and I made a few scratches in it by bumping it with a wrench.

Also, I would recommend painting every side the same color, and not just leaving primer on one side like I did, because the primer is visible when the wheel is assembled.

I'll make another post after the paint has dried a bit more and I've mounted it on the bike.
Attachments
wheel 6.jpg
wheel 6.jpg (136.06 KiB) Viewed 1686 times
wheel 5.jpg
wheel 5.jpg (155.35 KiB) Viewed 1686 times
wheel 4.jpg
wheel 4.jpg (131.83 KiB) Viewed 1686 times
User avatar
johnk
Member
Posts: 166
Joined: Mon Sep 03, 2018 9:42 pm

Post by johnk »

I finished the job today.
Attachments
I should really fix that scrape.
I should really fix that scrape.
wheel 9.jpg (168.89 KiB) Viewed 1669 times
wheel 8.jpg
wheel 8.jpg (193.12 KiB) Viewed 1669 times
Primer showing through
Primer showing through
wheel 7.jpg (116.59 KiB) Viewed 1669 times
whereshaldo
Member
Posts: 25
Joined: Sat Aug 17, 2019 11:41 pm
Location: Seattle

Post by whereshaldo »

Oh we even have the same color! Those rims look good. Its amazing what painting rims will do to any vehicle. If you want to get fancy you can hand-paint an orange stripe in the concavity of the rim lip and it looks sharp. Just spin the wheel and let the paint lay itself down with a small brush.
User avatar
modsquad
Member
Posts: 27
Joined: Tue May 14, 2019 1:22 am
Location: california

painting spare

Post by modsquad »

I also painted my spare to match the scooter. But I ended up mounting it on my rear rack because I couldn't get to fit right where it's supposed to go...Bill
Attachments
101_9339_Easy-Resize.com (2).jpg
101_9339_Easy-Resize.com (2).jpg (9.48 KiB) Viewed 1652 times
I love the smell of 2 stroke oil in the morning
User avatar
modsquad
Member
Posts: 27
Joined: Tue May 14, 2019 1:22 am
Location: california

rear rack mounted spare

Post by modsquad »

here's another pic.
Attachments
r_101_9343.JPG
r_101_9343.JPG (110.17 KiB) Viewed 1645 times
I love the smell of 2 stroke oil in the morning
Post Reply