Roughhouse Custom Build - In progress
Moderator: Modern Buddy Staff
- buddyz
- Member
- Posts: 19
- Joined: Fri Jan 25, 2013 12:22 am
- Location: Bloomington, Indiana
- Contact:
Roughhouse Custom Build - In progress
I've been slowly tweaking things around with my RH50 and thought I'd share my progress so far. The first two photos are most recent. I'll also show what the Rattler bars looked like before I went with the NCY bars.
So far:
Eliminated the long back fender tail
Swapped tail light with R6 led taillight. (has blinkers and tail in one)
Swapped stock tires with Vee Rubber street tires
NCY low down shock in rear
NCY carbon front forks (Also lowered)
Swapped steering stem from Rattler 110
NCY bars
Custom Grips
LED lights below floor board
NCY Supertrans KIT
Dr. Pulley Slider weights
Shortened the side stand to compensate for lowering
In the near future I'm planning:
Custom rims
Colored external hardware
Possibly 8 inch rear wheel stretch
Possibly run a fatty rear wheel set up
I might be forgetting some other small mods I've done or plan to do.
So far:
Eliminated the long back fender tail
Swapped tail light with R6 led taillight. (has blinkers and tail in one)
Swapped stock tires with Vee Rubber street tires
NCY low down shock in rear
NCY carbon front forks (Also lowered)
Swapped steering stem from Rattler 110
NCY bars
Custom Grips
LED lights below floor board
NCY Supertrans KIT
Dr. Pulley Slider weights
Shortened the side stand to compensate for lowering
In the near future I'm planning:
Custom rims
Colored external hardware
Possibly 8 inch rear wheel stretch
Possibly run a fatty rear wheel set up
I might be forgetting some other small mods I've done or plan to do.
- Attachments
-
- rh3.jpg (101.84 KiB) Viewed 3256 times
-
- rh2.jpg (93.97 KiB) Viewed 3256 times
-
- rh1.jpg (139.61 KiB) Viewed 3256 times
Last edited by buddyz on Sun May 10, 2015 5:35 pm, edited 1 time in total.
Roughhouse 50: NCY Supertrans, 8 gram Dr. Pulley sliders, Low down shock, eliminated fender and reflectors, Bar end mirror, LED ground effects, Hidden tender port
- buddyz
- Member
- Posts: 19
- Joined: Fri Jan 25, 2013 12:22 am
- Location: Bloomington, Indiana
- Contact:
Rattler bars
If anyone wondered how the Rattler bars looked on here I tried it but decided to go a different route.
- Attachments
-
- rh6.jpg (88.73 KiB) Viewed 3254 times
Roughhouse 50: NCY Supertrans, 8 gram Dr. Pulley sliders, Low down shock, eliminated fender and reflectors, Bar end mirror, LED ground effects, Hidden tender port
- buddyz
- Member
- Posts: 19
- Joined: Fri Jan 25, 2013 12:22 am
- Location: Bloomington, Indiana
- Contact:
For Comparison
Here's how it stacks up next to a stock Roughhouse
- Attachments
-
- rh8.jpg (77.96 KiB) Viewed 3253 times
Roughhouse 50: NCY Supertrans, 8 gram Dr. Pulley sliders, Low down shock, eliminated fender and reflectors, Bar end mirror, LED ground effects, Hidden tender port
- wheelbender6
- Member
- Posts: 852
- Joined: Sun Jul 07, 2013 1:27 am
- Location: Houston area
- buddyz
- Member
- Posts: 19
- Joined: Fri Jan 25, 2013 12:22 am
- Location: Bloomington, Indiana
- Contact:
- buddyz
- Member
- Posts: 19
- Joined: Fri Jan 25, 2013 12:22 am
- Location: Bloomington, Indiana
- Contact:
You'll need to splice a few wires for the turn signals and brake/running light to all be one unit.
eedo17 wrote:I am trying to do the same thing with an integrated tail light... was it as simple as a remove and plug in job or did you have to do some modifications to the housing or wiring?
Looks great!
Roughhouse 50: NCY Supertrans, 8 gram Dr. Pulley sliders, Low down shock, eliminated fender and reflectors, Bar end mirror, LED ground effects, Hidden tender port
-
- Member
- Posts: 18
- Joined: Mon Mar 12, 2018 12:50 am
- Location: Chicago
Any New Mods?
Did you end up doing the extension? Would love to see pics of anything new!
-
- Member
- Posts: 3
- Joined: Wed Jun 05, 2019 4:39 am